source: trunk/MultiChannelUSB/oscilloscope.v@ 86

module oscilloscope
        (
                input   wire                    clk, reset,
                input   wire                    data_ready, trigger,
                input   wire    [15:0]  data,
                input   wire    [9:0]   address,
                output  wire    [9:0]   start_address,
                output  wire    [15:0]  q
        );
        
        // signal declaration
        reg             [3:0]   state_reg, state_next;
        reg                             wren_reg, wren_next;
        reg             [9:0]   addr_reg, addr_next;
        reg             [15:0]  data_reg, data_next;

        reg                             trig_reg, trig_next;
        reg             [9:0]   trig_addr_reg, trig_addr_next;
        reg             [9:0]   counter_reg, counter_next;

        wire    [15:0]  q_wire;

        altsyncram #(
                .address_reg_b("CLOCK0"),
                .clock_enable_input_a("BYPASS"),
                .clock_enable_input_b("BYPASS"),
                .clock_enable_output_a("BYPASS"),
                .clock_enable_output_b("BYPASS"),
                .intended_device_family("Cyclone III"),
                .lpm_type("altsyncram"),
                .numwords_a(1024),
                .numwords_b(1024),
                .operation_mode("DUAL_PORT"),
                .outdata_aclr_b("NONE"),
                .outdata_reg_b("CLOCK0"),
                .power_up_uninitialized("FALSE"),
                .read_during_write_mode_mixed_ports("OLD_DATA"),
                .widthad_a(10),
                .widthad_b(10),
                .width_a(16),
                .width_b(16),
                .width_byteena_a(1)) osc_ram_unit(
                .wren_a(wren_reg),
                .clock0(clk),
                .address_a(addr_reg),
                .address_b(address),
                .data_a(data_reg),
                .q_b(q_wire),
                .aclr0(1'b0),
                .aclr1(1'b0),
                .addressstall_a(1'b0),
                .addressstall_b(1'b0),
                .byteena_a(1'b1),
                .byteena_b(1'b1),
                .clock1(1'b1),
                .clocken0(1'b1),
                .clocken1(1'b1),
                .clocken2(1'b1),
                .clocken3(1'b1),
                .data_b({16{1'b1}}),
                .eccstatus(),
                .q_a(),
                .rden_a(1'b1),
                .rden_b(1'b1),
                .wren_b(1'b0));

        // body
        always @(posedge clk)
        begin
                if (reset)
        begin
                        state_reg <= 4'b1;
                        wren_reg <= 1'b1;
                        addr_reg <= 10'd0;
                        data_reg <= 16'd0;
                        trig_reg <= 1'b0;
                        trig_addr_reg <= 10'd0;
                        counter_reg <= 10'd0;
                end
                else
                begin
                        state_reg <= state_next;
                        wren_reg <= wren_next;
                        addr_reg <= addr_next;
                        data_reg <= data_next;
                        trig_reg <= trig_next;
                        trig_addr_reg <= trig_addr_next;
                        counter_reg <= counter_next;
                end
        end

        always @*
        begin
                state_next = state_reg;
                wren_next = wren_reg;
                addr_next = addr_reg;
                data_next = data_reg;
                trig_next = trig_reg;
                trig_addr_next = trig_addr_reg;
                counter_next = counter_reg;

                case (state_reg)
                        0:
                        begin
                                // nothing to do 
                                state_next = 4'b0;
                                wren_next = 1'b0;
                                addr_next = 10'd0;
                                data_next = 16'd0;
                                counter_next = 10'd0;
                        end
                        
                        1:
                        begin
                                // write zeros
                                if (&addr_reg)
                                begin
                                        wren_next = 1'b0;
                                        state_next = 4'd2;
                                end
                                else
                                begin
                                        addr_next = addr_reg + 10'd1;
                                end
                        end
        
                        2:
                        begin
                                if (data_ready)
                                begin
                                        wren_next = 1'b1;
                                        data_next = data;
                                        state_next = 4'd3;
                                end
                        end

                        3:
                        begin
                                // stop write
                                wren_next = 1'b0;
                                addr_next = addr_reg + 10'd1;

                                if (&counter_reg)
                                begin
                                        state_next = 4'd0;
                                end
                                else
                                begin
                                        state_next = 4'd2;

                                        if ((~trig_reg) & (trigger) 
                                                & (counter_reg == 10'd512))
                                        begin
                                                // trigger
                                                trig_next = 1'b1;
                                                trig_addr_next = addr_reg;
                                        end
                                        
                                        if (trig_reg | (counter_reg < 10'd512))
                                        begin
                                                counter_next = counter_reg + 10'd1;
                                        end
                                end
                        end

                        default:
                        begin
                                state_next = 4'b0;
                                wren_next = 1'b0;
                                addr_next = 10'd0;
                                data_next = 16'd0;
                                counter_next = 10'd0;
                        end
                endcase
        end

        // output logic
        assign  q = q_wire;
        assign  start_address = trig_reg ? (trig_addr_reg ^ 10'h200) + 10'd1: addr_reg + 10'd1;

endmodule