source: trunk/MultiChannelUSB/histogram.v@ 66

module histogram
        (
                input   wire                    clk, reset,
                input   wire                    data_ready,
                input   wire    [11:0]  data, address,
                output  wire    [23:0]  q
        );
        
        // signal declaration
        reg             [3:0]   state_reg, state_next;
        reg                             flag_reg, flag_next;
        reg                             wren_reg, wren_next;
        reg             [11:0]  addr_reg, addr_next;
        reg             [23:0]  data_reg, data_next;

        wire    [23:0]  q_a_wire, q_b_wire;
        
        wire    [11:0]  addr_wire;
        wire    [23:0]  data_wire;
        
        assign  addr_wire = (flag_reg) ? data : addr_reg;
        assign  data_wire = (flag_reg) ? (q_a_wire + 24'd1) : data_reg;

        altsyncram #(
                .address_reg_b("CLOCK0"),
                .clock_enable_input_a("BYPASS"),
                .clock_enable_input_b("BYPASS"),
                .clock_enable_output_a("BYPASS"),
                .clock_enable_output_b("BYPASS"),
                .indata_reg_b("CLOCK0"),
                .intended_device_family("Cyclone III"),
                .lpm_type("altsyncram"),
                .numwords_a(4096),
                .numwords_b(4096),
                .operation_mode("BIDIR_DUAL_PORT"),
                .outdata_aclr_a("NONE"),
                .outdata_aclr_b("NONE"),
                .outdata_reg_a("UNREGISTERED"),
                .outdata_reg_b("UNREGISTERED"),
                .power_up_uninitialized("FALSE"),
                .read_during_write_mode_mixed_ports("OLD_DATA"),
                .widthad_a(12),
                .widthad_b(12),
                .width_a(24),
                .width_b(24),
                .width_byteena_a(1),
                .width_byteena_b(1),
                .wrcontrol_wraddress_reg_b("CLOCK0")) hst_ram_unit(
                .wren_a(wren_reg),
                .clock0(clk),
                .wren_b(1'b0),
                .address_a(addr_wire),
                .address_b(address),
                .data_a(data_wire),
                .data_b(),
                .q_a(q_a_wire),
                .q_b(q_b_wire),
                .aclr0(1'b0),
                .aclr1(1'b0),
                .addressstall_a(1'b0),
                .addressstall_b(1'b0),
                .byteena_a(1'b1),
                .byteena_b(1'b1),
                .clock1(1'b1),
                .clocken0(1'b1),
                .clocken1(1'b1),
                .clocken2(1'b1),
                .clocken3(1'b1),
                .eccstatus(),
                .rden_a(1'b1),
                .rden_b(1'b1));

        // body
        always @(posedge clk)
        begin
                if (reset)
        begin
                        flag_reg <= 1'b0;
                        wren_reg <= 1'b1;
                        addr_reg <= 12'd0;
                        data_reg <= 24'd0;
                        state_reg <= 4'b1;
                end
                else
                begin
                        flag_reg <= flag_next;
                        wren_reg <= wren_next;
                        addr_reg <= addr_next;
                        data_reg <= data_next;
                        state_reg <= state_next;
                end
        end

        always @*
        begin
                flag_next = flag_reg;
                wren_next = wren_reg;
                addr_next = addr_reg;
                data_next = data_reg;
                state_next = state_reg;
                case (state_reg)
                        0:
                        begin
                                // nothing to do
                                flag_next = 1'b0;
                                wren_next = 1'b0;
                                addr_next = 12'd0;
                                data_next = 24'd0;
                                state_next = 4'd0;
                        end
                                                
                        1:
                        begin
                                // write zeros
                                if (&addr_reg)
                                begin
                                        flag_next = 1'b1;
                                        wren_next = 1'b0;
                                        state_next = 4'd2;
                                end
                                else
                                begin
                                        addr_next = addr_reg + 12'd1;
                                end
                        end     

                        2:
                        begin
                                if (data_ready)
                                begin
                                        if (&q_a_wire)
                                        begin
                                                flag_next = 1'b0;
                                                state_next = 4'd0;
                                        end
                                        else
                                        begin
                                                wren_next = 1'b1;
                                                state_next = 4'd3;
                                        end
                                end
                        end

                        3:
                        begin
                                wren_next = 1'b0;
                                state_next = 4'd2;
                        end

                        default:
                        begin
                                flag_next = 1'b0;
                                wren_next = 1'b0;
                                addr_next = 12'd0;
                                data_next = 24'd0;
                                state_next = 4'd0;
                        end
                endcase
        end

        // output logic
        assign  q = q_b_wire;
endmodule